Robot welder workshop welding fume extraction,Portable
welding smoke collector
**Application Place:
LB-JF high vacuum model dust collector , mainly applied to purification dry, no oil, no corrosion of the smoke gas during welding, cutting and grinding process.
LB-JF high vacuum model dust collector is industrial processing, welding dust removal, cutting dust, grinding dust removal of the preferred products.
Robot welder workshop welding fume extraction,Portable welding smoke collector
**Products Advantage:
1),LB-JF high vacuum model dust collector adopted international advanced polyester fine filtering technique, can be effective absorption and filtration the smoke micro (0.2 um) of the welding, cutting and grinding process, filtration efficiency can reach 99.9%. At the same time and high gas flow is guaranteed.
2), the purifier has low noise, stable performance, convenient operation and use and many other advantages.
3), this product is double filter, the first level for Mars filter and larger particles, secondary to tiny dust filter.
**Operating Principle:
Under the device's high negative pressure, the fume and dust through suction pipe into the purifier, with the Martian dust before enter the purifying cavity were blocked and separated by fire sand. The remaining dust flow is blocked and uniform distribution by flow plate inside the purifying cavity, in order to better purify by cartridge filter.
Larger particles of dust under the action of gravity sinking into the collection of ash hopper, while small particles of dust under the action of suction generated by the eddy current is suspended in internal to purify by cartridge filter.
Small particles of dust on the surface of the filter cartridge, after the effect of gathered adsorption and combined, sinking into the ash hopper. After purification, the air flow out, offer a healthy working environment for workers.
LB-JF high vacuum model dust collector , mainly applied to purification dry, no oil, no corrosion of the smoke gas during welding, cutting and grinding process.
LB-JF high vacuum model dust collector is industrial processing, welding dust removal, cutting dust, grinding dust removal of the preferred products.
**Technical Parameter:
| Model | Airflow M³/h | Power KW | Voltage V/Hz | Kpa | Ash removal model | compressed air (mpa) | Dimension (mm) | Noise (dbA) |
| JF190 | 190 | 1.5 | 380/50 | 23000 | automatic blow | 0.5-0.6 | 550*550*1100 | <72 |
| JFS245 | 245 | 3.0 | 380/50 | 32000 | 0.5-0.6 | 550*550*1100 | <75 |
The welding fume extractor/ purifier is easy of installation, and has no technical requirements when the customer install and use it. The flexible extraction arm is made from high quality material of PVC and steel wire, which is anti-corrosion, heat-resistant of up to 140°C. It can swivel 360º and can be brought in any desired direction without additional support. It is equipped with the damper to adjust the wind. It is equipped with the caster wheels and can be freely mobile to meet the requirements of different work places.
The purified gas can meet the standard requirements and can enter into work room or indoor place, which is helpful to keep the room close, maintain the temperature and be convenient for work.
Operating Principle:
Under the help of the fan device, the welding fume is sucked into inlet through multi-direction sucking hood. There is the flame arrester in the inlet, so the spark can be blocked here, and the left fume and dust is sucked into gravity separator. The bigger paticiles firstly descend into dust bag. The smaller particles is arrested in the surface of core filter. The cleaner gas then flow into clean room after being purified by core filter. In clean room, the clean gas is then further purified by active carbon. At last, the gas meets the required standards and enter into air or other required room.
The BasicStage Filtration Process about the welding fume extractor
Stage 1: Air passes trhough the pre-filter fire-proof net.
Stage 2: Air passes through a second pre-separator to further reduce medium to heavy particulate matter.
Stage 3: Air passes through the LongLife-H filter where welding fume particles are captured and deposited.
Stage 4: Activated carbon filter will help prevent or neutralize the release of odors back into the environment.
Videoes:
The work video about the welding fume extractors for the welding condition, which have a good performance :
http://loobo.cn/video/gyhb/600.htm
http://loobo.cn/video/gyhb/606.htm
https://youtu.be/yLBAvptRM-M
The company development film :
http://loobo.cn/video/693.htm
Facility Characteristics about the welding fume extractors
1) It is equipped with ABB turbo fan and motor imported from Germany and America, with overload prevention circle to avoid motor damage. It is of steady performance.
2) It is equipped with built-in centralized PLC controlling system. The operation panel is clear and simple, very easy to operate.
3) Pulsing back-flushing automatic dust-removal system: The filter core is the automatic rotating and back-flushing type, which keeps the filter core surface clean when working, to insure the stable blowing rate; The air compressor parts are connected with high pressure rubber pipe with high pressure air-inflow in the bottom, which insure the facility always in good working condition.
4) The filter core is imported from the large company in America with long useful life. It can arrest the 0.3μm particles. The filtering effect is good for all kinds of particles including the wet particles.
5) It is equipped with the all-directions sucking arm of 360 degree rotating. It can suck the fume exactly from the source which make best of the fume collection efficiency, and insure the workers’ health in the largest extent.
6) It is equipped with three layer filter system to avoid the damage effect of flame and large slag particles, which extend the useful life, more safe and more reliable.
7) The clean air is exhausted uniformly and diffusely through the gridiron outlet, so it can minimize the noise.
8) It is attached with all-direction caster wheels, which makes the facility movable freely and easy to position.
9) Photoelectric controlled on/off, energy saving and high efficiency. The hood has the lighting device which is upon customer’s choice.
10) The parts working condition are all stable and has long useful life, meantime easy to be replaced.
Custom design and production for the welding fume extractor is available according your requirement
Other main welding fume extractors:
1. LB-JZX model(double cartridge filters fume extractor for metal welding, welding workshop cleaner machine ):
| Model | Airflow(m3/h) | Power(kw) | Voltage(v/hz) | Size(mm) | Noise(dB(A)) |
| LB-JZX2400 | 2400 | 2.2 | 380/50HZ | 900*800*1480 | 75 |
| LB-JZX3600 | 3600 | 3.0 | 380/50HZ | 900*800*1480 | 78 |
| LB-JZX4800 | 4800 | 4.0 | 380/50HZ | 900*800*1480 | 78 |
| LB-JZX2400S | 2400 | 2.2 | 380/50HZ | 900*800*1480 | 75 |
| LB-JZX3600S | 3600 | 3.0 | 380/50HZ | 900*800*1480 | 78 |
| LB-JZX4800S | 4800 | 4.0 | 380/50HZ | 900*800*1480 | 78 |
The JZX models welding fume extractor is one updated model from LB-JZ models, which have a high performanec than the LB-JZ series welding fume extractors
2.LB-BG model(wall mounted welding smoke eater type):
| Model | AirflowM³/h | VoltageV/HZ | PowerKW | Filter efficiency | Dimension(MM) | NoisedbA |
| BG1200 | 1200 | 380V/50 | 0.75 | 99.9% | 600*500*600 | <72 |
| BG1500 | 1500 | 380V/50 | 1.5 | 99.9% | 600*500*600 | <72 |
| BG2400 | 2400 | 380V/50 | 2.2 | 99.9% | 600*500*600 | <75 |
3.LB-JK model(with simple structure welding dust collector, air cleaner for metal fabriaction ) :
| Model | Airflow(m3/h) | Power(kw) | Voltage(v/hz) | Size(mm) | Noise(dB(A)) |
| LB-JK1200 | 1200 | 0.75KW | 220/50HZ | 530*640*1000 | 65 |
4.LB-JW model(Flat filter welding smoke exhauster for metal cutting):
| Model | Airflow M³/h | Power KW | Voltage V/Hz | Dimension (mm) | Noise (dbA) |
| JW1200 | 1200 | 1.1 | 380/50 | 700*700*1110 | <72 |
| JW1500 | 1500 | 1.5 | 380/50 | 700*700*1110 | <72 |
| JW2400 | 2400 | 2.2 | 380/50 | 700*700*1110 | <75 |
The main filters used on the welding fume extractors:
Shipping for the welding fume extractors:
Company Information
We,Qingdao Loobo Environmental Protection Technology Co.,Ltd is aimed to air purifying and kinds of removing fume exhausted, with its own R&D team more than ten years manufacturer, located in Qingdao city of china, specialized in the main products:
1,portable welding fume extractors,and soldering fume extractors etc.,
2.downdraft benches(grinding dust removal worktable),
3.central fume purification projects,
4.Spare parts:flexible suction arm,etc.
All of our products with the ISO9001, and CE certification for parts of products, the quality can be guaranteed.
ATTN: Miss Molly Huang
Tel: 86-15064847869
Skype: mollyhice
Email: hqhpl@126.com
|
|
Robot welder workshop welding fume extraction,Portable welding smoke collector Images
|
